The content down below about Tools You Need to Install a New Bathtub is immensely fascinating. Don't overlook it.
Installing a bathtub isn't specifically rocket science, but it does require solid plumbing, woodworking, and occasionally, tiling abilities. Replacing an old bath tub with a brand-new one is likewise a moderately tough project. If the old bathtub is readily easily accessible, the task can relocate quickly; if you have to open up a wall to remove the old tub and also place the new tub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly require a helper to vacate the old tub and also set in the brand-new one. Ensure you have qualified yourself for the task and are comfortable attempting it. As opposed to employing a specialist to take over a halfway-completed job, it is better to consider using one prior to you begin. Possibilities are you may require a specialist plumber to make tube connections.
This article will certainly help you install a new bathtub in your washroom if you have already gotten a new bathtub and do not require to transform the arrangement of your previous supply of water pipelines.
Your tools and product list ought to comprise the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your installment, after that the first thing you should do is separate the water. After doing so, activate the taps to drain any type of water staying in the system. The procedure of getting rid of the existing faucets can be quite troublesome due to the restricted access that is often the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a fabric all set for the continuing to be water that will originate from the pipes. When the supply pipes have been gotten rid of, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from transforming throughout this process. When the taps have actually been eliminated, the holes in the bath/basin will have to be cleaned of any type of old securing substance.
Before going on to fit the new faucets, contrast the pipeline connections on the old taps to the new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic adapter to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end offers a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washers remain in location in between the tap as well as the sink. Secure the faucet in place with the manufacturer given backnut. As soon as the faucet is firmly in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The previous type needs to be linked to the tap ends initially, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have been attached.
Mounting the Bath tub
Making use of the two wooden boards under its feet, put the bathtub in the required placement. The wooden boards are helpful in evenly spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 tiny points.
The following goal is to ensure that the bathtub is leveled all round. This can be attained by checking the level and also changing the feet on the bath tub until the spirit level checks out level.
To mount taps, fit the bottom of the outermost adaptable faucet connector to the proper supply pipeline by making a compression join; after that do the exact same for the various other tap.
Turn on the water system and also inspect all joints and new pipework for leaks as well as tighten them if needed. Load the bath tub as well as also check the overflow electrical outlet and the normal electrical outlet for leakages.
Lastly, repair the bath paneling as described in the supplier's instruction manual. Tiling as well as securing around the tub should wait up until the bath tub has been utilized at the very least once as this will certainly resolve it right into its last position.
Getting ready for the Installation
Firstly, the supporting frame supplied with the bathroom ought to be fitted (if required) according to the supplier's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is important to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps unit to prevent pressure on the tub.
Fit the versatile tap ports to the bottom of both faucets making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you make use of all of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should now be ready to be fitted in its last placement.
Tiling Around the Bath tub
In the area where the bathroom satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to split an inflexible seal, triggering the water to pass through the wall between the bathroom and the tiling, bring about complications with moisture as well as possible leakages to the ceiling below.
You can select from a variety of coloured sealants to assimilate your fixtures and installations. They are offered in tubes and also cartridges, as well as can securing spaces up to a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with twists of soaked newspaper or soft rope. Bear in mind to constantly load the tub with water before sealing, to allow for the motion experienced when the bathtub is in usage. The sealant can break relatively early if you do not take into account this activity before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally quickly available on the marketplace. It is recommended to fit the tiles making use of waterproof or waterproof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that article about Tools You Need to Install a New Bathtub while doing a search on the search engines. Loved our entry? Please share it. Help another person locate it. We cherish reading our article about A Step-by-Step Guide to Installing a Bathtub.
Reliable repairs? Dial.